Posted on

feminizing my marijuana seeds

With a bit of aforethought, it is possible to set up an efficient feminization breeding programme—and have female seeds from your favourite phenos on hand all the time. You never know, you might discover the next big thing!

Hint: Make two clones once a plant has been selected, one to be feminized and one to be left for pollination. This way, a separate breeding space is created and accidental seeding of other plants, or an accidental sneeze pollinating a whole grow cupboard, is avoided.

There are a number of harvesting methods employed to catch pollen.

FEMBOTS RULE

Colloidal silver is by far the easiest to source or make. It is non-toxic, non-caustic, and can be bought from a pharmacy or easily online. The other solutions can be dangerous, difficult to get a hold of, and expensive—except gibberellic acid, which can be found in nurseries, but is not as effective as colloidal silver. But if you want to watch some freaky plant growth just for the fun of it, give gibberellic acid a try. It is a growth stimulant and makes plants stretch and stretch.

Well, that is where the feminizing technique comes into play: two methods of manipulating the cannabis plant to produce only females from seed, every-time. To be truthful, it isn’t every single time. But 99% of the time is a pretty good number, and could be considered entirely male risk-free.

Feminized seeds are super efficient for indoor and outdoor gardeners. Area, time, and resources aren’t being given to plants that will be thrown away two weeks after the 12-12 flip. Similarly, outdoors where a large plant can consume a lot of time and resources in upkeep prior to the autumn show of flowers, feminized plants are also a good way to reduce guerrilla crop pollinating. There’s nothing worse than bush-bashing out to a well-hidden crop only to find a rogue male or two have impregnated every female plant.

  • Cover the top of the pot with plastic or card to catch pollen as it falls, or modify a plastic drink cup to shroud the plant and catch falling pollen.
  • Fix a clear plastic bag, perforated at the top for air exchange, around the whole plant.
  • An experienced eye will remove each flower pod prior to it bursting completely open to be sure of catching every spore.
  • Pollinating a female is the easy bit. Depending on how many seeds you want to make, there are a couple of methods that can be used.
  • Using a watercolour or other fine, soft brush or even a cotton bud, dip into your pollen collection and gently apply to the chosen flower. Although thousands of viable spores will be on the end of the brush, enough to pollinate a whole plant, the trichomes on the surface of the pistils will greedily glue everything you offer them. So dip into your pollen stash a few times as you dust.
  • For lots of seeds, put pollen in a bag and put over a whole branch or a whole plant, shake well, and leave for twenty four hours.
  • It is possible to pollinate different branches with different pollens and have a breeder plant that has 1, 2, or 15 different crosses on it.
  • It is also possible to self-pollinate the plant from which the male parts were created. This won’t produce as many seeds as pollinating a separate plant because less female flowers are produced and many are nonviable because of the feminization process.

This seed is about to burst out of its calyx!

You can choose to treat a single bud site or all the bud sites on the plant. Any untreated bud sites will develop into female buds as usual. If you want to smoke these buds, it’s incredibly important to avoid letting them come into contact with colloidal silver as that’s not safe to smoke. (Don’t worry, feminized seeds don’t contain any silver). I highly recommend letting the whole plant be your test subject so you don’t have to worry about that ?

Yes, it’s possible to use just female plants and feminized seeds for further breeding, with one major caveat.

When your chosen mother is 2-3 weeks into the flowering stage, take a paintbrush and ‘paint’ your feminized pollen on the developing bud sites you want to pollinate. Bud sites (for both male and female plants) are located wherever you can see leaves meet a stem.

4.) Pollinate Another Female Plant

Important! Keep spraying daily until pollen sacs open up. Don’t stop spraying early, even if pollen sacs appear to be already formed, otherwise they may not produce much pollen!

But the process of finding the right “father” is a little different when you start with two female plants. In this case you already know quite a bit about the genes of both parents because you can just look at and test the buds of both plants directly. This allows you to pinpoint desirable genes with less guessing and much less time spent growing out and cataloging plants!